Electronic equipment without battery-driven approach
Double-layer capacitor technology, the latest development has enabled it to replace the specific secondary power storage applications in rechargeable batteries (Reference 1). Capacitor provides a rechargeable battery as opposed to the obvious advantages,IBM Laptop Battery, including the actual infinite number of charge / discharge cycle, the viability of short-circuit cases, over-voltage protection only need a simple charging circuit. In addition, the storage capacitor can be recharged quickly,FRU 92P1141, FRU 92P1137, 02K6651, 02K6928, 02K6620, 02K7039
and when products arrive at the end of working life, it will not deal with problems caused by toxic waste.
This design example by describing a potent driver capacitor charger, which extends the earlier ideas. Power-driven generators and a combination of high-value capacitor for emergency equipment and survival kit provides a high degree of autonomy and keep the environment clean method of electricity supply. This alternative "renewable" energy applications cover a wide range of modern portable electrical and electronic equipment, including mobile phone, MP3 player, AM / FM Radio, PDA, handheld PC, flash.
Power supply capacitor charger contains only a few components: the storage capacitor, bridge rectifier,FRU 92P1141, the protection of high voltage capacitors from the effects of pressure limiting Zener diode (Figure 1). Energy Storage for the actual experiment, you can use the maximum rated voltage of 5.5 V of 1F or 0.47 F capacitor, such as NEC-Tokin America Inc. (www.nec-tokin.com) products (Figure 2). Such as the need for greater storage capacity, you will enable a higher capacity power capacitors, such as Elna Corporation (www.elna.co.jp) of the 100 F 2.5 V Dynacap (Figure 3).
You can put the artificial light from a cheap supply of electricity out of flash, and its generator as a capacitor charger (Figure 4). In addition, the current appearing on the market a variety of artificial supply products provide the possibility of doing experiments. For higher output, FRU 92P1141, FRU 92P1137, 02K6651, 02K6928, 02K6620, 02K7039
you can use a fixed bike-driven generators. According to individuals pedal power, these generators can provide 20W to 100W average power. Figure 4 in the crank-start-style flash was first lit a 2.5V, 0.15A tungsten foam, which when consumed in the whole brightness of about 0.4W. However, the measurement results show that: the generator can provide more power, and in about 10 seconds 1F capacitor to charge to 5V. FRU 92P1137,Calculate the following formula is stored in the capacitor (capacitance value of C) in the energy: E = 1/2C × VMAX2 = 12.5J, and the following formula can be calculated a variety of time an average of the largest power generating capacity T: TMAX = E / T = 12.5/10 = 1.25 W.
You can use the following formula to calculate the capacitor's terminal voltage from the highest to the lowest at the same time, capacitor in the discharge cycle can provide effective energy EEFF: EEFF = 1/2C (VMAX2-VMIN2), which VMAX2 and respectively represent VMIN2 to be imposed on electricity supply facilities in the maximum and minimum operating voltage. You can storage capacitors in series or parallel. In both cases, should ensure that the circuit for the capacitor that contains the appropriate over-voltage protection. In order to obtain additional voltage, you can add a DC / DC switching regulator to generate a stable output voltage. Some important design considerations on the diode bridge rectifier and Zener diode DZ highest voltage and current rating. Launch of the crank generators experimental measurement of its open-circuit voltage of the following approximation: a maximum voltage 10 Vrms,FRU 92P1141, FRU 92P1137, 02K6651, 02K6928, 02K6620, 02K7039
peak voltage 14 V, maximum short-circuit current 200 mArms. For such applications, a minimum peak value of 20V reverse voltage and forward current of 0.5 A minimum of cheap bridge rectifier to provide sufficient headroom. DZ breakdown voltage rating should be slightly lower than the maximum storage capacitor voltage, and diode rated power - in this application is 2 W - should be more than the maximum output current generator and the Zener diode conduction voltage product.
1. Fuel cell test system at home and abroad to ,02K6651,study the overall level of the status quo and
As the fuel cell is still in development stage, the auto industry has not yet formulated a standard fuel cell test equipment. Let alone a standardized testing equipment supplier. Many companies started to approach this challenge, research and accurate testing of fuel cell solutions. These companies attracted the most attention is the United States, Hydrogenics Corporation and National Instruments (NationalInstnlments, referred to as NI), they launched a number of hardware and software testing products. Can be compatible with a variety of fuel cells, measured in almost all design specifications: Hydrogenics of Greenljght is one of the world's largest fuel cell test systems cattle production base. It is the fuel cell test diagnostic equipment industry leading global suppliers. Nl adequate computer-based global leader in measuring carcasses, many of the leading fuel cell manufacturers are in various stages of development using NI hardware and software to test T with fuel cells. In the entire ibm battery industry to develop fuel cell test systems handful, H before 2004 are foreign manufacturers.02K6928, To enable the development of fuel cell experts can take advantage of measurement, control, analysis and visualization tools to assess, Wuhan Li Hing Test Equipment Co., Ltd keep the world's most cutting-edge fuel cell technology, independently developed the leading domestic level with the fuel cell test systems, FRU 92P1141, FRU 92P1137, 02K6651, 02K6928, 02K6620, 02K7039
and in January 2004 launched fuel cell test systems. The introduction of the system to fill in our country in the field of fuel cell test blank. In the promotion of the domestic fuel cell industry milestone have extraordinary significance.
2. Fuel cell test system's basic theory
2.1 testing purposes
Although the research, development, manufacture and application of the Department of the overall objective of f J different. Their fuel-cell detection and hide, as the project's requirements are similar. On the small R & D departments, testing requirements to determine adequate output energy, battery life and durability. Acceptance in the design stage, the main task is to optimize the design for mass production. Without lowering the efficiency and lower the total cost of the stack. On the small production applications. Requirements in line with the regulatory requirements of fuel cell. In actual use, the monitoring of battery life and work status is very important. Fortunately,02K6620, these different tasks on the battery test system requirements are similar.
2.2 The main features of Test System
① isolation. Fuel cell test systems have a variety of measuring signal conditioning needs of large water lizard. Then the original signal can be digitized data acquisition system. Darong most stack with hundreds of single cell. Thus the number of white-voltage measurement requirements. V common-mode rejection. Test not only must be more than able to read each channel l-10V channel. And must maintain each stack and the final between a battery of up to hundreds of volts of isolation.
② data acquisition system must be able to expand.FRU 92P1141, FRU 92P1137, 02K6651, 02K6928, 02K6620, 02K7039
As the fuel cell test system can access the number from 100 to more than 1000. Therefore, data acquisition system must be able to expand. And these systems can also signal attenuation and amplification.
③ modular. For today's test systems, modular is also essential.02K7039 , Because the testing system must be able to verify with the production and technological changes and changes.
④ calibration. Any test system should be calibrated to ensure efficient and accurate measurement.
No comments:
Post a Comment